News
CONTACT US
National Marketing Hotline:
International Sales Hotline:
After-sales Hotline:
Contact Email:
Contact Address:
NO.977 Qingwei Road, Jimo District, Qingdao City
A Comprehensive Guide to Choosing the Right High-Performance Skid Steer Loader
Release time:
2025-07-11
Data source:
The skid loader is known as the "sharp knife" product among small construction machinery. With its powerful functions and flexible and maneuverable characteristics, it is widely used in infrastructure construction, road and bridge, dock loading and unloading, municipal maintenance, sanitation, residential and other narrow construction environments... It is a multifunctional work platform that can meet different tasks. If the piston comes wear phenomenon, it will lead to the concrete cylinder wall and piston seal greatly reduced, and even appear the leakage problem.In addition, damage to the piston can affect the pumping capacity of the pump truck, as the concrete suction into the concrete cylinder decreases as the piston wears away.Piston general wear-resistant rubber, polyurethane, rubber and other materials, the diameter of the general than the cylinder diameter of 3-4mm.If excess concrete slurry is found in the tank, check to see if concrete pistons need to be replaced and if necessary.The piston lip should be pressed down first when replacing, and it should slide into the cylinder through one end of the cylinder.
The skid loader is known as the "sharp knife" product among small construction machinery. With its powerful functions and flexible and maneuverable characteristics, it is widely used in infrastructure construction, road and bridge, dock loading and unloading, municipal maintenance, sanitation, residential and other narrow construction environments... It is a multifunctional work platform that can meet different tasks.
So, how to choose the right skid loader equipment for the construction site? The key is to understand the performance of the equipment and the content of the project, such as simple soil piling, lifting objects, material handling, etc.
Ryan Ruhl from John Deere likes to use the efficiency of the equipment to choose a skid loader. "It is the most reasonable method to figure out the size of the project and then choose the most suitable equipment to complete it." He believes that using inappropriate skid loader equipment will not only get twice the result with half the effort, but also cost more. For example, if the selected skid loader has insufficient lifting performance (insufficient power or hydraulic flow), it will reduce the efficiency of the equipment and extend the construction period.
Therefore, when choosing a skid loader, you should pay attention to the following points.
1. Model and power size
What engineering project you do determines what kind of equipment you choose. Does the equipment need to work in a narrow building space? Does it need extra traction to push piled items on soft or muddy ground? Does it need a higher lifting height and dumping distance to load materials onto trucks? Does it need to pass through narrow door frames or perform foundation backfilling operations?
Small skid steers generally have a power of less than 50 horsepower, medium-sized products have a power range of 50 to 70 horsepower, and large skid steers usually have more than 70 horsepower. Understanding the needs of the work can help us choose the right machine.
2. Selection of radial lift arm and vertical lift arm equipment
The radial lift arm of the skid steer loader swings to the highest point in an arc before reaching the highest point, while the vertical lift arm directly lifts upward and then outward to the highest point. If your equipment only works from the ground to the top of the cab, then radial lift equipment is a good choice. If you often need to work above the cab or higher, then you need a device with a vertical lift arm to complete the work.
For example, a radial lift skid steer is better suited for short-distance gravel transport and other tasks, because at the lowest point, the bucket is closer to the machine, which can provide additional power. However, if you often use the equipment to shovel materials to load dump trucks, a vertical lift skid steer is better because the bucket can reach a higher position.
3. What attachments are you going to use?
Many customers will purchase different attachments in addition, and high-flow hydraulic systems can provide more flow for attachments. So if you expect the equipment to do more work, the hydraulic system is very important. It is worth mentioning that the performance of the attachment is affected by the hydraulic flow and the engine horsepower, and these two factors determine the best performance of the work attachment.
Our experience is that when the attachment is a trencher or milling machine, the hydraulic system needs to provide a larger flow and the engine needs to provide a larger power. In addition, other attachments that require high-flow hydraulics include: wheel shovels, trenchers, snow blowers, etc.
4. Driving comfort and equipment automation
Many manufacturers have found that users are increasingly concerned about driving comfort and equipment control automation. When the operator has a comfortable seat, a quiet cab, a good view and convenient automated controls, work can be made easier, so work efficiency will also be improved to a certain extent.
Other News
Prevent pump truck from spontaneous combustion
Regular inspect and maintain.Whether the fuel tank is leaking oil, whether the engine is hot, whether the electrical circuit is aging.Check whether the brake camshaft grease pipe is blocked.Note that the old grease must be cleaned before applying the new grease when the wheel hub is maintained.
Maintenance of mixer truck in autumn
1. Wiper should be loved The increase rain in the autumn will inevitably make the wiper take on more responsibility. The owner can place the wiper switch at various speed positions, pay attention to whether the wiper has vibration and abnormal noise during work, check whether the wiper maintains a certain speed at different speeds, observe the state of the wiper, and the wiper strut Whether there is a phenomenon of uneven swing or slip.
How Trailer Concrete Pumps Function: A Detailed Overview
The principle of the concrete pump is actually quite simple. The rough principle is quite simple, just like a syringe for injection, sucking in and then pumping out. There are two concrete cylinders, one sucking and the other pumping, and the two work alternately.
The secret of preventing the side turn of the pump truck
The tilt device for measuring the vehicle's level and the sensor for measuring the pressure on the supporting leg.The tilt sensor can sense the vehicle's level and send real-time horizontal Angle information, which can effectively avoid the tilting caused by ground slow decline.The function of the tilt sensor is to measure the tilt Angle of the vehicle in real time.The measurement accuracy of the tilt sensor is higher than 0.05 degrees.It can filter out small tremors caused by engine and pump tremors and trigger alarm when the Angle of left and right is greater than 3 degrees or the Angle of front and rear is greater than 5 degrees.
Key Practices for Small Loader Use and Care in the Initial Running-in Phase
After a small loader leaves the factory, it is generally stipulated that there is a running-in period (or running-in period) of about 12-50 hours, which is stipulated according to the technical characteristics of the small loader in the early stage of use. The running-in period is an important link to ensure the normal operation of the small loader, reduce the failure rate, and extend its service life. However, at present, some users ignore the special technical requirements of the running-in period of the new machine due to lack of common sense in the use of loaders, or because of tight construction period, or because they want to make profits as soon as possible. Some users even think that the manufacturer has a warranty period anyway, and the manufacturer is responsible for repairing the broken machine, so the machine is overloaded for a long time during the running-in period, resulting in frequent early machine failures. Even when the warranty period is about to come, long-term operation ignores maintenance, and the failure is exposed as much as possible to obtain the manufacturer's warranty. During the last warranty period, the equipment is normal, and after the warranty period, frequent failures will not only affect the normal use of the machine, but also shorten the service life of the machine. Therefore, full attention should be paid to the use and maintenance of the loader during the running-in period.
A Comprehensive Guide to Choosing the Right High-Performance Skid Steer Loader
The skid loader is known as the "sharp knife" product among small construction machinery. With its powerful functions and flexible and maneuverable characteristics, it is widely used in infrastructure construction, road and bridge, dock loading and unloading, municipal maintenance, sanitation, residential and other narrow construction environments... It is a multifunctional work platform that can meet different tasks. If the piston comes wear phenomenon, it will lead to the concrete cylinder wall and piston seal greatly reduced, and even appear the leakage problem.In addition, damage to the piston can affect the pumping capacity of the pump truck, as the concrete suction into the concrete cylinder decreases as the piston wears away.Piston general wear-resistant rubber, polyurethane, rubber and other materials, the diameter of the general than the cylinder diameter of 3-4mm.If excess concrete slurry is found in the tank, check to see if concrete pistons need to be replaced and if necessary.The piston lip should be pressed down first when replacing, and it should slide into the cylinder through one end of the cylinder.
Easy to damage parts and maintenance of pump truck
1. The piston If the piston comes wear phenomenon, it will lead to the concrete cylinder wall and piston seal greatly reduced, and even appear the leakage problem.In addition, damage to the piston can affect the pumping capacity of the pump truck, as the concrete suction into the concrete cylinder decreases as the piston wears away.Piston general wear-resistant rubber, polyurethane, rubber and other materials, the diameter of the general than the cylinder diameter of 3-4mm.If excess concrete slurry is found in the tank, check to see if concrete pistons need to be replaced and if necessary.The piston lip should be pressed down first when replacing, and it should slide into the cylinder through one end of the cylinder.
Essential Principles of Aerial Platform Trucks Explained
Aerial work vehicles are special vehicles used to carry personnel, tools and materials to the work site and perform aerial work. Aerial work vehicles use a standardized automobile chassis as a walking mechanism to achieve walking (transfer) and carrying functions. In addition to the automobile chassis, in order to achieve the aerial work function, the composition of the aerial work vehicle also includes a power system, a working mechanism, a mechanical structure, a hydraulic and electrical control system, and a safety device.